Links and resources

Parts suppliers

Feked - huge range of parts for classic British bikes, reasonable prices and friendly
L. P. Williams - Triumph parts specialist. Sometimes has lower prices than Feked, worth checking
Brit Bikes - Another classic British bike parts place. Good for Lucas parts
Classic Bike Shop - Yet another, not tried this one yet
Classic British Spares - and another! This one has a great information section too.

Specialist parts and services

MS Motorcycles - THE place to get the correct paint colours for your classic Triumph
Amal carbs - Original parts for Amal carbs
Saftek Industrial Friction Products - for relining of brake shoes and skimming of brake drums
Thomas Hamlin & Co - superb old-school engineers for all manner of engine rebuilding

Information and forums

Terry Macdonald - a super-experienced restorer shares pictures of all his projects
Spanner and Socket sizes - get your head around the imperial standards
Classic British Spares (CBS) - this is a US-based parts supplier, but has lots of useful technical information too.
Classic Motorcycle Build - another US site offering really good general advice on restoring classics.
Triumph Owner Motorcycle Club - Since 1949! UK club offering rideouts, dating certificates, discounts and incredibly useful forum advice
classicbike.biz - invaluable free source for PDF owners manuals, workshop manuals and parts books for all Triumphs and Nortons

Fun stuff

The Motorbike Show with Henry Cole. Watch the first dozen shows online.
Contemporaneous magazine review of the ‘71 TR6R, from classicbike.biz

Comments

Post a Comment

Popular posts from this blog

All going swimmingly

Image
It's been a while since I posted, thankfully because there has been no more bad news! I have had the tank and mudguards repainted to the original design by Jayson Dowson ( Jayson D Designs ) who did an absolutely flawless job, thoroughly recommended. I have also done a bit of work on the primary chain side - that is the chain that transfers the power from the crankshaft to the clutch and gearbox. These old Triumphs have a cunning design where the clutch, gearbox input shaft, gearbox output shaft and front drive sprocket are all co-axial which take a bit of time to get your head around!  The clutch The gearbox The primary chain turns the clutch outer basket (clutch part 5), and unless the clutch lever is pulled in this torque is transferred through the clutch plates (14 & 15) via a rubber cush drive (6, 10) to the clutch inner hub (12), which is bolted to the end of the gearbox input shaft (gearbox part 1). The drive then passes from the input shaft to a separate parallel laysha...
Read more

Hundred-mile-stone reached (part 1)

Image
I've just come back from a lovely ride through the autumnal Chiltern hills, throughout which Bagheera performed faultlessly and was in her element chugging characterfully along the sunny backroads. The journey also brought up 100 miles since the engine was completely rebuilt following the disasterous overheat back in July. A frankly regrettable amount of time, pain and money has been needed to reach this point. As detailed in the last post , the engine overheat caused extensive damage to the top-end of the engine; damage beyond my ability or tools to repair. After a bit of searching around, I finally got a recommendation for a good engineer/machinist called H T Howard in Slough. After a quick chat with boss Andy, I was reassured that they really knew their onions, or more importantly their vintage British bikes. My first task was to source new engine internals. Due to the scuffing on the cylinder walls I decided to go up to the first oversize piston, officially specified by Trium...
Read more

Hundred mile stone reached (part 2)

Image
…and it started up first kick! I kid you not, nobody was more surprised than me. The correct thing to do after starting a rebuilt engine is to ride it straight away. Letting the engine idle does no good, it just generates heat which the new piston rings can’t get rid of because they are not yet worn in.  However I have an important check to do before can ride anywhere - I need to check the ignition timing. When I fitted the electronic ignition system, it included alignment markings to get the timing about right, but not spot on. Having had the engine failure before while running it ‘about right’ I was keen to check it before putting the rebuild engine through its paces.   An over-advanced ignition can damage the engine because the spark plugs set fire to the mixture while the piston is still moving up, causing a lot of pressure on the piston and rod and generating a lot of wasteful heat. It can even melt a hole right through the piston.  The timing is checked using a...
Read more